How To Adjust a Cobra OPTM Driver (Adjustment Guide)

Need to know how to adjust a Cobra OPTM Driver to switch the loft and lie angles? We have a complete guide to the FutureFit33 hosel.

The Cobra OPTM drivers range is fully adjustable with a hosel offering you the opportunity to adjust the loft to increase or decrease your launch angle.

The amount of golf driver adjustment you can make differs from brand to brand but the step-by-step guide below shows you how the Cobra OPTM drivers can be adjusted.

The FutureFit33 hosel is the most adjustable yet with up to 33 different loft and lie settings.

Cobra OPTM Drivers Lofts

The OPTM LS and X are available in 9 degrees and 10.5 degrees.

The Max-D and Max-K are available in 9 degrees, 10.5 degrees and 12 degrees.

All four are then fully adjustable to the following:

Cobra OPTM X Driver Specs

Loft: 9 degrees & 10.5 degrees

Standard Length: 45.5 inches

Standard Lie: 57 degrees standard lie

Adjustability: 7-11 degrees of loft and 55-59 degrees of lie & 8.5-12.5 degrees of loft and 56-60 degrees of lie

Cobra OPTM LS Driver Specs

Loft: 9 degrees & 10.5 degrees

Standard Length: 45.5 inches

Standard Lie: 57 degrees standard lie

Adjustability: 7-11 degrees of loft and 55-59 degrees of lie & 8.5-12.5 degrees of loft and 55-59 degrees of lie

Cobra OPTM Max-D Driver Specs

Loft: 9 degrees, 10.5 degrees & 12 degrees.

Standard Length: 45.50 inches

Standard Lie: 61 degrees standard lie

Adjustability: 7-11 degrees of loft and 59-63 degrees of lie, 8.5-12.5 degrees of loft and 59-63 degrees of lie & 10-14 degrees of loft and 59-63 degrees of lie

Cobra OPTM Max-K Driver Specs

Loft: 9 degrees, 10.5 degrees & 12 degrees

Standard Length: 45.50 inches

Standard Lie: 58 degrees standard lie (9 degree loft) & 59 degrees standard lie (10.5 degrees & 12 degrees lofts)

Adjustability: 7-11 degrees of loft and 56-60 degrees of lie, 8.5-12.5 degrees of loft and 57-61 degrees of lie & 10-14 degrees of loft and 57-61 degrees of lie

Adjusting The Loft Angle of a Cobra OPTM Driver

There are a few simple steps you can take to adjust the loft angle of your driver. You will just need an adjustment tool or wrench to get started.

Here’s how to adjust a Cobra OPTM driver:

1. Locate the screw on the sole of your Cobra OPTM driver that attaches the driver head to the shaft.

2. Using the wrench, loosen the screw by turning anticlockwise.

3. Once the screw is fully out, you can rotate the adjustable hosel to a lower loft or a higher loft depending on your preference. You will notice the loft figure you had the driver set to and be able to turn the shaft to up to 33 further options.

The available options from the FutureFit33 hosel adjustment are:

Examples:

• Fight a Slice: Use upright lie settings or closed face angles (e.g., B1, C1, or C8) to promote a draw
• Fix a Hook: Use flatter lie settings or open face angles (e.g., A8, A7, or B6) to promote a fade
• Maximize Distance / High Launch: Increase loft (move up the chart, e.g., F4 or G3)
• Control in Wind / Low Launch: Use lower loft settings like G3, G4 or F3

4. When you have turned the hosel to your required loft and lie setting, slot the shaft back into your club head. Your new loft will be displayed through the window on most drivers.

5. Put the screw back in place and tighten with the wrench by turning clockwise. When it is fully tight, you will hear a crank that sounds like the driver is cracking. At this point, the screw is as tight as needed.

Every time you want to adjust the loft or lie, you repeat this process.